Twitter

EnglishFrenchGermanItalianPortugueseSpanish

Monel Steel 500



We are the best destination to procure supreme quality Monel Steel 500. Our Monel Steel 500 is acknowledged for its high strength corrosion fatigue and erosion resistance. We make available Monel Steel 500 in different forms such as forgings, fasteners, wires and bars to cater to the wide demands of the clients.


Characteristics
  • Excellent mechanical properties from sub-zero temperatures up to about 480C.
  • Corrosion resistance in an extensive range of marine and chemical environments. From pure water to non-oxidising mineral acids, salts and alkalis.

Applications
  • Propeller and pump shafts.
  • Pumps and valves used in the manufacture of perchlorethylene, chlorinated plastics.
  • Typical application for the alloy which takes advantage of high strength and corrosion resistance are pump shafts, impellers, propeller shafts, valve components for ships and offshore drilling towers, bolting, oil well drill collars and instrumentation components for oil and gas production. It is particularly well suited for centrifugal pumps in the marine industry because of its high strength and low corrosion rates in high-velocity seawater.
  • The alloy is non-magnetic. The alloy should be annealed when welded and the weldment then stress relieved before aging.
  • High Performance Alloys, Inc. stocks Alloy K-500 in a range of sizes including 3/8"-2-1/2" diameter cold drawn, annealed and aged, and 2-3/4"-10" diameter hot finished and aged. Material can be supplied in random lengths, cut to order or machined to your specifications. Machining includes drilling, turning, tapping, threading, CNC shapes, flanges and more.

Chemistry

Chemical Requirements
NiMnSiFeAlSC
Max1.500.502.003.150.0100.18
Min63.002.30


Tensile Data

Mechanical Property Requirements
Ultimate TensileYield Strength (0.2% OS)Elong.Hardness Rockwell C, min.Hardness Brinell 3000 kg, min.
Cold Worked/SR Over 1(25.4) to 3
Min140 KSi100 KSi17.029280
Max
Min965 MPa690 MPa
Max
Hot Worked/ Aged Hardened
Min140 KSi100 KSi20.027265
Max
Min965 MPa690 MPa
Max


Specifications

Form Standard
Metal Type UNS N05500
Bar ASTM B865 QQ-N-286
Wire AMS4676
Sheet ASTM B865 QQ-N-286
Plate ASTM B865 QQ-N-286
Fitting
Forging QQ-N-286 Din 17754
Weld Wire FM 60 ERNiCu-7
Weld Electrode FM 190 ENiCu-7 Din 17753
Din 2.4375
Ratings
Nickel & cobalt base corrosion, temperature and wear-resistant alloys are classified as moderate to difficult when machining, however, it should be emphasized that these alloys can be machined using conventional production methods at satisfactory rates. During machining these alloys work harden rapidly, generate high heat during cutting, weld to the cutting tool surface and offer high resistance to metal removal because of their high shear strengths. The following are key points which should be considered during machining operations :
  • Capacity : Machine should be rigid and overpowered as much as possible.
  • Rigidity : Work piece and tool should be held rigid. Minimize tool overhang.
  • Tool Sharpness : Make sure tools are sharp at all times. Change to sharpened tools at regular intervals rather than out of necessity. A 0.015 inch wear land is considered a dull tool.
  • Tools : Use positive rake angle tools for most machining operations. Negative rake angle tools can be considered for intermittent cuts and heavy stock removal. Carbide-tipped tools are suggested for most applications. High speed tools can be used, with lower production rates, and are often recommended for intermittent cuts.
  • Positive Cuts : Use heavy, constant, feeds to maintain positive cutting action. If feed slows and the tool dwells in the cut, work hardening occurs, tool life deteriorates and close tolerances are impossible.
  • Lubrications : Lubricants are desirable, soluble oils are recommended especially when using carbide tooling.

Recommended Tool Types and Machining Conditions

OperationsCarbide Tools
Roughing, with severe interruptionRoughing, with severe interruption
Normal roughing

Turning or Facing C-2 or C-3 grade: Negative rate square insert, 45 degree SCEA, 1/32 in nose radius. Tool holder: 5 degree neg. back rake, 5 degree neg. side rake. Speed: 90 sfm depending on rigidity of set up, 0.010 in. feed, 0.150 in. depth of cut. Dry, oil, or water-base coolant.

Finishing

Turning or Facing C-2 or C-3 grade: Positive rake square insert, if possible, 45 degree SCEA, 1/32 in. nose radius. Tool holder: 5 degree pos. back rake, 5 degree pos. side rake. Speed: 95-110 sfm, 0.005-0.007 in. feed, 0.040 in. depth of cut. Dry or water-base coolant.

Rough Boring

C-2 or C-3 grade: If insert type boring bar, use standard positive rake tools with largest possible SCEA and 1/16 in. nose radius. If brazed tool bar, grind 0 degree back rake, 10 degree pos. side rake, 1/32 in. nose radius and largest possible SCEA. Speed: 70 sfm depending on the rigidity of setup, 0.005-0.008 in. feed, 1/8 in. depth of cut. Dry, oil or water-base coolant.

Finish Boring

C-2 or C-3 grade: Use standard positive rake tools on insert type bars. Grind brazed tools as for finish turning and facing except back rake may be best at 0 degrees. Speed: 95-110 sfm, 0.002-0.004 in feed. Water-base coolant.

Facing Milling

Carbide not generally successful, C- grade may work. Use positive axial and radial rake, 45 degree corner angle, 10 degree relief angle. Speed: 50-60 sfm. Feed: 0.005-0.008 in. Oil or waterbase coolants will reduce thermal shock damage of carbide cutter teeth.

End Milling

Not recommended, but C-2 grades may be successful on good setups. Use positive rake. Speed: 50-60 sfm. Feed: Same as high speed steel. Oil or water-base coolants will reduce thermal shock damage.

Drilling

C-2 grade not recommended, but tipped drills may be successful on rigid setup if no great depth. The web must thinned to reduce thrust. Use 135 degree included angle on point. Gun drill can be used. Speed: 50 sfm. Oil or water-base coolant. Coolant-feed carbide tipped drills may be economical in some setups.

Reaming

C-2 or C-3 grade: Tipped reamers recommended, solid carbide reamers require vary good setup. Tool geometry same as high speed steel. Speed: 50 sfm. Feed: Same as high speed steel.

Tapping

Not recommended, machine threads, or roll-form them.

Electrical Discharge Machining

The alloys can be easily cut using any conventional electrical discharge machining system (EDM) or wire (EDM).

Plasma Arc Cutting

Our alloys can be cut using any conventional plasma arc cutting system. The best arc quality is achieved using a mixture of argon and hydrogen gases. Nitrogen gas can be substituted for hydrogen gases, but the cut quality will deteriorate slightly. Shop air or any oxygen bearing gases should be avoided when plasma cutting these alloys.


Note
  • SCEA - Side cutting edge angle or lead angle of the tool.
  • At any point where dry cutting is recommended, an air jet directed on the tool may provide substantial tool life increases. A water-base coolant mist may also be effective.
  • Oil coolant should be premium quality, sulfochlorinated oil with extreme pressure additives. A viscosity at 100 degrees F from 50 to 125 SSU.
  • Water-base coolant should be premium quality, sulfochlorinated water soluble oil or chemical emulsion with extreme pressure additives. Dilute with water to make 15:1 mix. Water-base coolant may cause chipping and rapid failure of carbide tools in interrupted cuts.
  • M-40 series High Speed Steels include M-41 , M-42, M-43, M-44, M-45 and M-46 at the time of writing. Others may be added and should be equally suitable.
  • Oil coolants should be a premium quality, sulfochlorinated oil with extreme pressure additives. A viscosity at 100 degree F from 50 to 125 SSU.
  • Water-base coolants should be premium quality, sulfochlorinated water soluble oil or chemical emulsion with extreme pressure additives. Dilute with water to make 15:1 mix.